Can I Install a Bath Tub Myself? Considerations And Also Steps
Can I Install a Bath Tub Myself? Considerations And Also Steps
Blog Article
Just about every person has got their own opinion when it comes to A Step-by-Step Guide to Installing a Bathtub.
Setting up a bathtub isn't precisely brain surgery, however it does call for strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably difficult task. If the old tub is conveniently available, the task can move rapidly; if you have to open up a wall surface to eliminate the old bathtub and place the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and also set in the new one. Ensure you have actually qualified yourself for the job as well as fit trying it. Rather than employing a contractor to take over a halfway-completed job, it is far better to think about using one prior to you begin. Possibilities are you might need an expert plumber to make tube connections.
This write-up will help you set up a brand-new bathtub in your restroom if you have currently acquired a brand-new tub as well as do not need to change the plan of your previous water pipes.
Your tools as well as product list should comprise the following:
Preparing for the Setup
First of all, the sustaining structure provided with the bath ought to be fitted (if needed) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps unit to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its last placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be rather troublesome due to the restricted access that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to carrying on to fit the new faucets, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Using both wooden boards under its feet, position the tub in the required placement. The wooden boards are handy in evenly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as adjusting the feet on the tub until the level reads level.
To mount taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the supply of water and also check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the bath tub and likewise examine the overflow outlet as well as the regular outlet for leakages.
Finally, repair the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the bath tub should wait up until the tub has actually been used at the very least once as this will certainly settle it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end gives a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin guaranteeing that the washers remain in area in between the faucet as well as the sink. Safeguard the faucet in position with the maker supplied backnut. As soon as the faucet is firmly in position, the supply pipes can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet adapters. The previous kind must be linked to the tap ends first, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to break a rigid seal, causing the water to pass through the wall surface between the bath and the tiling, bring about issues with dampness as well as possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and also cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill the bathtub with water prior to securing, to enable the movement experienced when the tub remains in use. The sealant can crack rather very early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently readily available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our section on How to Install a Bathtub. Thank you for taking time to browse our blog. Sharing is caring. Helping people is fun. Thank you for your time invested reading it.
Explore
Report this page